2.5 inch Machino Nozzle Jet and Spray Branch Pipe   1.Product Description Machino Nozzle Branch pipe,its inlet connection is 2 1/2” storz / male instantaneous / male machino and outlet is Solid Jet nozzle. Material of construction is aluminum alloy.   2.Product Parameter    Model Number WFN - MBP25 Weight:  1.5 kg Fire nozzle body Material Aluminum Fire Nozzle Bumper Material Rubber  Coupling Storz, Instaneous, Machino Working Pressure  8 Bar Max Reach @ Max Flow 40 m Fire Nozzle Type Branch Pipe Spraying Type Jet / Fog   3.Products Features  A. Its operating pressure is 8bar to 12bar jet and spray type with rubber handle,It is a basic fire fighting nozzle commonly used by most fire Brigades. B. This nozzle is available with two orifice sizes:16mm or 19mm C. Application:hydrant system,wet or dry riser system 

Lance Variomatic UNI 45 PVC Rotating Fire Nozzle   1.Product Introduction  This is a device used to supply water, provided with a nozzle with a suitable section and a unified connection. The lance can also be equipped with a valve that allows the full jet, the split jet and the closure.   2.Product Parameter  Material PVC Size 45mm  Working pressure 16 Bar Test pressure 24 Bar Discharge pattern Jet Spray   3. Product Feature Made of polyamide resin with rubber gaskets. Its robustness and ergonomic design makes it highly manoeuvrable by extreme impact resistance. The passage from closed to full jet or vaporized and is regulated by the rotation of the neck at the front.

2.5'' Brass Thread Inlet Oblique Fire Hydrant Landing Valve Landing valves are suitable for installation on wet risers in a building for fire fighting purposes, permanently charged with water from a pressurized supply. The landing valves are oblique type with threaded inlet and are manufactured with delivery hose connection and blank cap. The landing valves are classified under low pressure and are suitable for use at nominal inlet pressure up to 15 bar.   Technical Data Valve Type Oblique, Threaded Inlet Pressure Rating Low Pressure Valve Nominal Size DN 2 1/2" Working Pressure 15 Bar Maximum Test Pressure Valve Seat Test at 16.5 Bar • Body Test at 22.5 Bar Water Flow Rate 8.5 L/S @ 4 Bar Outlet Pressure

2.5 Inch Straight Through Landing Valve Straight through landing valve is available in two types screw and flanged. There are suitable for installation on wet risers in a building or a hydrant, manufactured to comply to BS 5041 Part 1:1987 standard with delivery hose connection and blank cap complying with BS 336:2010 standard.   Product Parameter Code No. WFLV - ST25 Body Material Copper Alloy Inlet 2.5”BSP male thread or flanged according to BS4504 Outlet 2.5”BS 336 Female coupling with plastic cap &   chain Pressure Rating Low Pressure Valve Test pressure Valve Seat Test at 16.5   Bar • Body Test at 22.5   Bar Water Flow Rate 8.5 L/S @ 4 Bar Outlet   Pressure   Products Features Body material : copper alloy Hand wheel :grey cast iron  Blank cap material :copper alloy  The hand wheel is BLACK painted and body to RED

2.5 Inch Flange Inlet Oblique Fire hydrant Landing Valve The landing valves are pressure reducing type designed to provide a range of outlet pressure (5 bar -8 bar). The Landing valves are classified under high pressure and are suitable for use at nominal inlet pressure up to 20 bar. High quality with most favourable price. Pressure reducing oblique landing valves are suitable for installation on wet risers in buildings for fire fighting purposes, permanently charged with water from a pressurised supply.   Code No. Inlet Outlet WFLV - PR25 BS4504 PN16 65MM 2.5”BS336 INST.FEMALE WFLV - PR25A BS4504 PN16 80MM 2.5”BS336 INST.FEMALE WFLV - PR25B Male BSP Thread 65mm 2.5”BS336 INST.FEMALE  Valve type:Oblique flanged inlet Pressure Rating:HP or LP Nominal Size:DN65 Test pressure:valve seat test at 22bar,body test at 30bar Flange drilling:BS4504   Product Features: 1. Suitable for inlet pressure up to 20bar 2.Reduced outlet static pressure can be set from 5 to 8bar 3.Outlet pressure remain constant with inlet pressure range from 7bar to 20bar 4. Pressure test to 30bar 5.Minimum Flowrate up to 1400L/M 6.Body : Copper Alloy to BS 1400 7.Handwheel : Grey Cast Iron to BS 1452 8.Inlet:Male 2.5"BSP 9.Outlet : Female instantaneous to BS 336 and other connections

Dry Riser Inlets 4 Way Breeching Inlet Breeching inlets are suitable for installation on dry risers only, in a building for fire fighting purposes, fitted with inlet connection at fire brigade access level and outlet connection at specified points, which is normally dry but capable of being charged with water by pumping from fire service appliances. The breeching inlets are manufactured to comply with BS 5041 PART-3:1975 standard comprising of male instantaneous connections complying with BS 336:2010, drain valves complying with BS 5154, PN16 rated and non return valves. The breeching inlets and its fittings are suitable for a normal working pressure of 10 bar.   Products Features Body material made of spheroidal graphite cast iron (Ductile Iron) to BS 1563:2011 Inlet connection and non-return valves material made of copper alloy to BS 12163:2011 Each inlet connections are fitted with non-return valve and are of spring loaded mushroom type Each breeching inlet is painted RED internally and externally   Product Parameter Code No. WFBL- 4 Body Material Cast Iron Inlet  4 x 2 1/2" Male   instantaneous connections to BS336 each with spring-loaded non-return valve   and blanking cap & chain Outlet Flanged 6"  BS10  Table F or 150mm    BS4504  PN16 Pressure Rating Normal Working Pressure   of 16 Bar Test pressure 24 Bar Flange Drilling BS 4504 Part: 2:1974   Table: 16/21

2 Way Breeching Inlet for Riser Two Way Inlet Breeching Valve comply fully with the requirements of BS5041 Part 3. The bodies are manufactured from cast iron or spheroildal graphite iron and all fittings are in gunmetal making these inlet breechings extremely durable.   The 2-way dry riser inlet breeching has 2 x 2½” Instantaneous male non return valve inlets and a 4″ PN16 or Table D outlet flange. The 4-way inlet breeching has 4 x 2½” Instantaneous male non return valve inlets and a 6″ PN16 or Table D outlet flange. The 2-way and 4-way also comes complete with 1″ drain valve.   Product Parameter Code No. WFBL- 2 Inlet 2 Nos.   2-1/2” Male Instantaneous Connector Complying to BS 336 Outlet 100mm Flange outlet Working Pressure 16 Bar Test pressure Hydrostatically tested   to 24,Non-return valve tested to 22.5 bar Flange size BS 4504 / BS10D TABLE D   Products Features Manufactured in accordance with BS 5041 : Part 3 : 1975. High quality casting finishes. 25 mm drain valve with blanking cap and chain. Vertical or horizontal mounting.

2 Inch Brass Oblique Fire Valve Storz Fire Valve is a connector to fire water supply with the valve interface, used for factory, warehouse, high-rise buildings, public buildings and ship, normally installed in fire hydrant box, with fire hoses and water gun or wait for equipment supporting the fire equipment .   Type: Fire Valve Storz Model: WFHV - B50 Material: Brass Inlet interface: 50 mm / 2 inch Rated working pressure: 1.6 Mpa For water and foam mixed liquid only Standard: Manufacture and certified to DIN 14461    Name Indoor fire hydrant Body Material Brass Valve Rod Material Brass Size 50mm Packing Carton with pallet Delivery time 15-20 days OEM Avaliable Original Made In China

Wet Pipe System Fire Alarm Check Valve The alarm check valve is a water flow alarm device designed for vertical installation in the main supply to a wet pipe sprinkler system. When a flow of water from the system equals or exceeds that of a single sprinkler, the valve is to actuate a fire alarm. Model Norminal Diameter (mm) Working Pressure (MPa) Drive Time(s) ZSFZ-100 DN100 1.2~1.6 <15 ZSFZ-125 DN125 1.2~1.6 <15 ZSFZ-150 DN150 1.2~1.6 <15 ZSFZ-200 DN200 1.2~1.6 <15 Technical Data     Body Material Ductile Iron  Pipe Material Stainless Steel 304 Ball Valve Material Brass Fire Alarm Bell Material Stainless Steel 304 Retarder Material Stainless Steel 304 Pipe & Elbow Stainless Steel 304 Size (mm) DN100,DN125,DN150,DN200 Production Standard GB5135.5~2003

Pre-action Systems Fire Alarm Check Valve Pre-action sprinkler systems are specialized for use in locations where accidental activation is especially undesirable, such as in museums with rare art works, manuscripts, or books; and data centers, for protection of computer equipment from accidental water discharge.   Pre-action systems are hybrids of wet, dry, and deluge systems, depending on the exact system goal.    Model Norminal Diameter   (mm) Working Pressure   (MPa) Drive Time(s) ZSFY-100 DN100 1.2~1.6 <15 ZSFY-150 DN150 1.2~1.6 <15 ZSFY-200 DN200 1.2~1.6 <15

One Way Non Return Swing Check Valve Rubber disc check valve is mainly composed of body, cover and rubber disc three parts.Rubber disc is made by steel plate, steel bar and the reinforced nylon fabric substrate.This valve is usually installed in the outlet of the pump or inlet of water pool to prevent the water backflow and avoid damages to the pump caused by the water hammer phenomenon. The water flow in water supply or irritation networks often starts or stops abruptly causing hydraulic hammer shock, the main factor for breakage and damages of the pumps and pipes. The check valve with the rubber blocking eliminates the pump and network destruction risks because it receives and absorbs all the created high pressure functioning like the shock absorber of an automobile. The rubber disc check valve is designed to provide the best possible protection to pump installations and water networks.   Advantages: Absorbs part of the hydraulic surge waves Silent operation Smooth liquid flow Little maintenance required Applications: Irrigation Water supply networks Pump stations

Ductile Iron Flange Silent Check Valve Silent Check Valves are designed to prevent water hammer in multi-story buildings and for use in vertical turbine pump installations when pumping from a well to an elevated reservoir. Silent Check Valves are recommended for commercial and industrial HVAC applications such as heating systems and condensate return lines. The valve closes silently, is low in cost, reliable and requires no regular maintenance. When the pump stops, the spring forces disc closed against slight pump head at zero velocity which results in silent closure.

Ductile Iron Y Type Strainer This product is designed for remove foreign matter from pipe lines and provides protection for pumps, meters, valves, and other similar mechanical equipment, which is called as Strainer. "Y" Type Strainers are named after their shape and normally used for course filtration. But with large filtration area can be used with fine mesh also.   The Strainer improves the clearance in the medium, and prolongs the life of valves; protect expensive pumps, meters and other equipments.  A Y-strainer can be installed in either a horizontal or vertical position (Downward flow) with the screen elementpointing downward. This allows the strainer screen to collect material in the strainer at the lowest point of the screen.

Ductile Iron Groove Type Signal 6 Inch Water Gate Valve The signal gate valve is mainly used in the pipeline of the fire water system as a function of opening and intercepting the fluid in the pipeline, and converting the opening and closing working state into an electric signal through the signal device. The elastic seat sealing gate valve signal gate valve encapsulating the whole valve disc to generate a deformation compensation effect to achieve a good sealing effect, overcome the general gate valve sealing failure, water leakage, and rust phenomenon, more effective saving installation space.   It's mainly composed by the signal device, valve body, valve cover, disc assembly, stem, stem nut, hand wheel and other components. The annunciator is mainly composed of a transmission gear, a transmission rod and a micro switch. Gate Valve Applications Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services. Some special gate valve is used in slurry and powder product also such as knife gate valve Advantages of Gate Valve Gate valve provides good pressure drop during operation  Most of the gate valve can be used as bi-directional They are suitable for high pressure and temperature application and required less maintenance

8 Inch Flange Type Signal Gate Valve The signal gate valve is mainly used in the pipeline of the fire water system as a function of opening and intercepting the fluid in the pipeline, and converting the opening and closing working state into an electric signal through the signal device. The elastic seat sealing gate valve signal gate valve encapsulating the whole valve disc to generate a deformation compensation effect to achieve a good sealing effect, overcome the general gate valve sealing failure, water leakage, and rust phenomenon, more effective saving installation space.   It's mainly composed by the signal device, valve body, valve cover, disc assembly, stem, stem nut, hand wheel and other components. The annunciator is mainly composed of a transmission gear, a transmission rod and a micro switch. Gate Valve Applications Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services. Some special gate valve is used in slurry and powder product also such as knife gate valve Advantages of Gate Valve Gate valve provides good pressure drop during operation  Most of the gate valve can be used as bi-directional They are suitable for high pressure and temperature application and required less maintenance    Product Parameter   DN L H H1 W C n-D E T F 50 178 233 123 203 125 4-φ19 165 19 3 65 190 233 93 203 145 4-φ19 185 19 3 80 203 270 100 203 160 8-φ19 200 20 3 100 229 322 110 203 180 8-φ19 220 20 3 125 254 355 125 280 210 8-φ19 250 20 3 150 267 401 143 280 240 8-φ19 285 20 3 200 292 516 170 330 295 8-φ23 340 21 3 250 330 638 203 382 355 12-φ23 406 26 3 300 356 717 230 420 410 12-φ28 460 26 4 350 381 844 260 420 470 16-φ28 520 26.5 4 400 406 935 282 420 525 16-φ31 580 28 4

Ductile Iron 6 Inch Flange OS&Y Gate Valve One type of valve commonly used to control water flow to fire sprinkler systems is known as an OS&Y gate valve. OS&Y means “outside stem and yoke” or "outside screw and yoke".   OS&Y gate valves operate by opening and closing via a gate, which lowers into or rises out of the valve. Raising the gate allows water to flow through the valve while lowering the gate cuts off the water flowing through the valve. When fully open, the typical gate valve has no obstruction in the flow path, resulting in very low friction loss.   Products Features - Precision-machined valve stem, reduces operating torque. - Non-toxic powder epoxy resin spraying on botn inside and outside of the valve to enhance corrosion resistance and improve water quality. - The valve plate is covered with rubber both inside and outside to guaranteed good sealing. It has strong connection to avoid fall off after long-term use. - Thrust bearings reduce frictional resistance and reduce operating torque.   Product Parameter   DN D D1 NO.×NXφ L H(Close) H(Open) 40 150 110 4×18 178 322 374 50 165 125 4×18 178 322 374 65 185 145 4×18 190 332 395 80 200 160 8×18 203 350 429 100 220 180 8×18 229 420 524 125 250 210 8×18 254 581 721 150 285 240 8×22 267 581 736 200 340 295 12×22 292 736 942 250 405 355 12×26 325 880 1013 300 460 410 12×26 356 1009 1117 350 520 470 16×26 385 1300 1655 400 580 525 16×30 406 1380 1805 450 640 585 20×30 432     500 725 650 20×33 457     600 840 770 20×36 508